Anisa, Deddy Nan Setya Putra Tanggara, Dody Ariyantho Kusma Wijaya, Noveriady, Asri Fridtriyanda

Analisis Geometri Jalan Tambang Batubara Pada Kegiatan Overburden Removal di PT Satria Alam Manunggal Site TOP Desa Buhut Jaya Kabupaten Kapuas Provinsi Kalimantan Tengah

Engineering

This study was conducted at PT Satria Alam Manunggal Site TOP to analyze the effect of road geometry conditions on the performance of Scania P410-B6x4...

View Full Research

Nilesh Sonara, Dilip Joshi, Narendrasinh Desai

Modified B-Spline Collocation Solution of Countercurrent Imbibition Phenomenon with Inclined and Without Inclined in Homogeneous Porous Medium

Engineering

During the process of secondary oil recovery, water is injected into the reservoir formation to displace the remaining oil. When water enters such a p...

Review:

The paper, "Modified B-Spline Collocation Solution of Countercurrent Imbibition Phenomenon with Inclined and Without Inclined in Homogeneous Porous Me...

View Full Research

Jauharotul Maknunah, Karsid Karsid, Cokro Aminoto, Siti Rachel Sufyani

SISTEM MONITORING Ph DAN TEMPERATUR PADA PROTOTYPE IPA BERBASIS BERBASIS PROGRAMMABLE LOGIC CONTROLLER OUTSEAL

Engineering

Penelitian ini bertujuan untuk merancang dan mengimplementasikan sistem monitoring suhu dan pH pada Instalasi Pengolahan Air (IPA) menggunakan Program...

View Full Research

faldi daud suiyoso sianturi, Sely Novita Sari, Ridayati Ridayati

PERANCANGAN OPTIMAL GUDANG LOGISTIK KEBENCANAAN BPBD KABUPATEN BANTUL UNTUK EFISIENSI PENYIMPANAN DAN DISTRIBUSI LOGISTIK KEBENCANAAN

Engineering

Badan Penanggulangan Bencana Daerah (BPBD) Kabupaten Bantul merupakan badan yang bertugas mendistribusikan bantuan kebencanaan saat terjadi...

View Full Research

Triani Aulya Fitri, Ahmad Syahrul Mubarok

TRANSFORMASI SISTEM FILTRASI BLOWDOWN: PENDEKATAN BACKWASH UNTUK MENINGKATKAN EFISIENSI DAN DAYA TAHAN

Engineering

Proses filtrasi pada sistem blowdown berfungsi untuk memisahkan udara yang diolah dari partikel halus polimer yang dihasilkan setelah prose...

View Full Research

Tito Alfarizi, Hendra Setyawan, Oldy Fahlovi, Ganjar Kurnia, Nugroho Tri Atmoko

PEMANFAATAN LIMBAH SEA WATER DAN ENGINE OIL PADA INDUSTRI PETROKIMIA UNTUK PROSES QUENCHING PADA BAJA S45C

Engineering

Studi tentang penggunaan baja karbon S45C pada industri manufaktur telah mengalami perkembangan yang peesat. Tidak hanya pemanfaatan pada k...

Review:

This study presents an intriguing investigation into the utilization of waste materials from the petrochemical industry for the heat treatment of S45C...

View Full Research

Veryawan Nanda Perkasa, Ita Wijayanti , Hanifah Widiastuti, Meschac Timothee Silalahi

ANALISIS PENGARUH SUDUT MASUK HALUAN TERHADAP HAMBATAN KAPAL MENGGUNAKAN SOFTWARE MAXSURF

Engineering

Optimasi geometri lambung kapal merupakan strategi krusial untuk meningkatkan efisiensi hidrodinamis dan mengurangi konsumsi bahan bakar da...

Review:

The submitted paper, "ANALISIS PENGARUH SUDUT MASUK HALUAN TERHADAP HAMBATAN KAPAL MENGGUNAKAN SOFTWARE MAXSURF," presents a timely and relevant inves...

View Full Research

Hanifah Madriyah Intan Permata Sari, Cintiya Septa Hasannah

the Initiation of Direct Contact Heat Exchanger Addition at the Evaporation Station of the X Sugar Mill

Engineering

White crystal sugar is one of the plantation commodities that is widely produced because it is widely consumed by the people of Indonesia. White cryst...

Review:

This manuscript addresses a pertinent issue within the sugar industry, focusing on enhancing the efficiency of the evaporation station at X Sugar Mill...

View Full Research

Themy Sabri Syuhada

Performance Analysis of Long Short-term Memory (LSTM) Model for Remaining Useful Life Prediction on Turbofan Engine

Engineering

Accurate Remaining Useful Life (RUL) prediction is critical for the predictive maintenance and operational safety of aircraft turbofan engines. This r...

View Full Research

Muhammad Lukman, Abdul Hamid, Muhammad Showi Nailul Ulum

OPTIMASI PAREMETER PENGELASAN SMAW TERHADAP HASIL UJI TARIK MENGGUNAKAN METODE TAGUCHI PADA POSISI 3G

Engineering

This research aims to optimize the Shielded Metal Arc Welding (SMAW) process parameters on tensile strength using the Taguchi method in the 3G welding...

Review:

This research, titled "OPTIMASI PAREMETER PENGELASAN SMAW TERHADAP HASIL UJI TARIK MENGGUNAKAN METODE TAGUCHI PADA POSISI 3G," presents a systematic i...

View Full Research